Plastic mesh sleeve R-PLS 12x50mm - plastic bag - 10 pcs.
R-PLS-12050-10
5906675377520
Define product parameters:
Catalog price for bx:
PLN16.70
net | VAT 23
Contact with us and check out our terms of cooperation
R-PLS-12050-10
5906675377520
Define product parameters:
Catalog price for bx:
PLN16.70
net | VAT 23
Contact with us and check out our terms of cooperation
Catalog price for bx:
PLN16.70
net | VAT 23
Contact with us and check out our terms of cooperation
Metric threaded rod, hexagonal head, steel A4 STUDS 8x160mm - paper box - 10 pcs.
Metric threaded rod, hexagonal head, steel class 8.8 STUDS 8x110mm - paper box - 10 pcs.
Metric threaded rod, hexagonal head, steel class 5.8 STUDS 8x160mm - paper box - 10 pcs.
18 V RawlHAMMER 2.0J 20mm Cordless rotary hammer drill, Set with RawlCASE, 2 batteries 5.0Ah and 6.5 A RawlCHARGER - plastic case - 1 pc.
Brickdrill SDS PLUS non-impact drill bits 12x260 mm - plastic hanger - 1 pc.
Polyester bonded anchor R-KEM-II standard - plastic cartouche - 300 ml
Product info
Plastic mesh sleeve Maxxfast for use with threaded rods in hollow substrates
Installation and use of polyester chemical anchor – Rawlplug's tutorial
Non-cracked concrete
Hollow brick
Clay block
Concrete hollow floor block (eg. Teriva)
Hollow lightweight concrete block (Use category D)
Masonry
Aerated concrete
Approved surfaces
Anchoring glued in with threaded rods
Balustrades
Barriers
Blinds and awnings
Blinds / curtain rods
Scaffolding
Ventilated facades
Air conditioning / ventilation
Steel mesh sleeve 10mm 1 m for M8 rod - paper box - 10 pcs.
Steel mesh sleeve 12mm 1 m for M8-M10 rod - paper box - 10 pcs.
Drill a hole to the required diameter and depth for rebar size being used.
Choose extensions and brushes to the selected depth and diameter of the hole, then combine them into one set.
Before inserting anchor, clean inside of hole by commpresed air starting from the drill holle botton. Blow the hole at least twice by compressed air at minimum 6 bar.
Choose extensions and brushes to the selected depth and diameter of the hole, then combine them into one set.
Connect the drill set with the SDS tip.
Before inserting anchor, clean inside of hole by commpresed air starting from the drill holle botton. Blow the hole at least twice by compressed air at minimum 6 bar.
Drill a hole to the required diameter and depth for rebar size being used.
Place the sleeve in the hole.
Place the threaded rod in the sleeve and wait until the resin is fully cured according to the information on the package.
Dispense resin 100% of the hole depth and close the sleeve plug.
After full curing of the anchor, install the fixed element with a proper torque.
Fill hole with the required resin to the recommended fill level. (Follow the relevant instructions for the resin product).
Insert the threaded stud slowly and with a slight twisting motion, until the required embedment depth is reached.
Leave to solidify for the time required for the application.
Attach fixture and tighten the nut to the required torque.
Item is properly attached.
Chemical anchors, general characteristics and application - E-LEARNING
Chemical anchors, basics of anchoring technology - temperature - E-LEARNING
Chemical anchors basics of anchoring technology - substrates - E-LEARNING
Chemical anchors basics of anchoring technology - rods- E-LEARNING
Chemical anchors general installation rules - E-LEARNING
Chemical anchors - introduction and correct installation of anchors - ON-SITE TRAINING
Chemical anchors - introduction and correct installation of anchors - TRAINING CENTER