1. Mainpage
  2. Vinylester bonded anchor R-KER standard - plastic cartouche - 300 ml

Vinylester bonded anchor R-KER standard - plastic cartouche - 300 ml

Solid walls

R-KER-300

5906675075167

Polyester bonded anchor without styrene, recommended for medium loads, for use in concrete

Define product parameters:

Packaging and quantity

Related products

Manual gun for bonded anchor resin in cartridges 175-310ml - label - 1 pc.

Professional manual gun for bonded anchors.

Pump for blowing drill cuttings - plastic bag - 1 pc.

Manual blow pump for cleaning dust from drilled holes

Manual gun for cartridges: 385/600ml(3:1), 280/300/310ml, 380-410ml (10:1), 4.5kN - cardboard box - 1 pc.

Professional manual gun for resin anchors in cartridges 385/600ml(3:1), 280/300/310ml, 380-410ml (10:1), 4,5kN

Metal brush for cleaning holes M12 - label - 1 pc.

Metal brush with handle for cleaning holes in a solid substrate

Rebardrill SDS Plus drill bits 18x250x310 mm - plastic hanger - 1 pc.

High-quality SDS plus drill bits for drilling in reinforced concrete

Metric threaded rod, hexagonal head, steel class 8.8 STUDS 16x190mm - cardboard box - 10 pcs.

Threaded rod made of class 8.8 steel for use with bonded anchors

18 V RawlHAMMER 2.0J 20mm Cordless rotary hammer drill, Set with RawlCASE, 2 batteries 5.0Ah and 6.5 A RawlCHARGER - plastic case - 1 pc.

18V SDS plus Cordless hammer drill "RawlHammer"

Aggressor SDS Plus drill bits 18x250x310 mm - plastic hanger - 1 pc.

Drill bits SDS plus for fast drilling in concrete

Metric threaded rod, hexagonal head, steel class 8.8 STUDS 20x260mm - cardboard box - 5 pcs.

Threaded rod made of class 8.8 steel for use with bonded anchors

Turbodrill SDS Max drill bit 24x200x340 mm - plastic hanger - 1 pc.

SDS max drill for drilling deep holes in reinforced concrete, concrete, stone and hard brick

Metric threaded rod, hexagonal head, steel A4 STUDS 20x260mm - cardboard box - 5 pcs.

Threaded rod made of A4 stainless steel for use with bonded anchors

Rebardrill SDS Max drill bit 18x200x340 mm - plastic hanger - 1 pc.

SDS max drill with 3 symmetrically arranged cutting edges allow, for drilling holes in reinforced concrete, concrete, stone and hard brick

Features

Polyester bonded anchor without styrene, recommended for medium loads, for use in concrete

  • Approved for use with rebar as an anchor for use in non-cracked concrete
  • Suitable for use in dry and wet substrates including flooded holes (use category I1 & I2).
  • Rapid bonding time enables quick execution of works
  • Very high load capacity
  • Anchor does not generate expansion forces in the concrete which means reduced spacing and edge distances.
  • Suitable for multiple use. Partly used product can be reused after fitting new nozzle

Product video

Jak prawidłowo użyć kotwy chemicznej?

Jaką kotwę chemiczną wybrać?

Czym jest kotwa chemiczna i jak jej używać?

Rawlplug R-KER Vinylester Resin - Rebar Installation

Rawlplug R-KER Styrene Free Vinylester Resin and Rebar

Substrates

Non-cracked concrete

Non-cracked concrete

Approved surfaces

Applications

Anchoring glued in with reinforcing bars

Anchoring glued in with threaded rods

Balustrades

Barriers

Concrete structures

Electrical Installations

Elevators and escalators

Formwork

Gates

Handrails

Pipelines

Pitched roofs

Reinforcement of a large slab

Sanitary and gas installations

Steel structures

Ventilated facades

Substitutes

Services

Design Consulting

Design Consulting

Resin calculator

Resin calculator

E-learning training

E-learning training

Learn more
Training at the Rawlplug Academy center

Training at the Rawlplug Academy center

Installation guide

Installation manual

Installation step by step

1

Blow out the dust at least 4 times with the hand pump.

2

Drill a hole to the required diameter and depth for rebar size being used.

3

Clean drilled hole 4 times.

4

Remove drill cuttings from the hole using the hand pump four times.

5

Place the cartridge in the dispenser.

6

Dispense to waste until even colour is obtained.

7

Fill with resin 70% of the depth of the hole, starting from the bottom of the hole.

8

Immediately after dispensing the resin, insert the rod into the hole with a twisting motion.

9

Remove the unnecessary amount of resin that flowed from the hole and wait for the appropriate time for the resin to cure.

10

Immediately insert the rebar, slowly and with slight twisting motion. Remove any excess resin around the hole before it sets and leave it undisturbed until the curing time elapses.

11

Place the bar in the hole and allow the setting time to elapse.

12

Attach fixture and tighten the nut to the required torque.

13

Drill a hole of appropriate diameter and depth.

14

Wydmuchać pył co najmniej 4 razy przy pomocy ręcznej pompki.

15

Usunąć zwierciny z otworu za pomocą czterokrotnego użycia wyciora

16

R_KEX_385_stud_inst_draw_04

17

Umieścić kartridż w dozowniku i przymocować dyszę mieszającą

18

Rozpoczynając dozowanie z nowego opakowania odrzucić część żywicy, aż do uzyskania jednakowego koloru mieszanki

19

Insert the mixing nozzle to the far end of the hole and inject resin, slowly withdrawing the nozzle as the hole is filled to 70% of its depth.

20

Immediately after dispensing the resin, insert the rod into the hole with a twisting motion.

21

Leave the anchor undisturbed unitl the curing time elapses.

22

Reinforcing bar is properly installed in the concrete base.

Approvals and publications

Technical library and approvals

Choose document:

ETA-10/0055

1488-CPR-0161/W

DoP-10/0055-R-KER

ETA-12/0319

1488-CPR-0738/W

DoP-12/0319-R-KER

ETA-13/0805

1488-CPR-0695/W

DoP-13/0805-R-KER

UKTA-0836-22/6107

UKTA-DoP-22/6107-R-KER

UKTA-0836-22/6110

UKTA-DoP-226110-R-KER

KOT-2018/0134

KDWU-2018-0134-1

Hygienic Certificate - R-KER

Fire Evaluation Report - R-KER

VOC Emission Test Report - R-KER

SDS_R-KER_CFS_01.03.2023

Product card and catalogues

Choose product card:

Product card R-KER with Rebar as an Anchor

Product card R-KER with Threaded Rods

Product card R-KER with Internally Threaded Sockets (ITS)

Product card R-KER with Post-Installed Rebars

Choose product catalog:

Specification Design Guide

General catalogue - PDF

Stay up to date

Sign up for our newsletter and don't miss:

Information

on our products and services

News

on the offering and latest promotions

Reports

on events, trade shows and industry conferences

© 2024 Koelner Rawlplug IP