1. Mainpage
  2. Polyester bonded anchor R-KEM-II winter version - plastic cartouche - 410 ml

Polyester bonded anchor R-KEM-II winter version - plastic cartouche - 410 ml

Universal

R-KEM-II-410-W

5906675516271

Polyester bonded anchor without styrene, recommended for medium loads, suitable for use in most construction substrates

Define product parameters:

Bonded anchors version
Packaging
Resin color
Packaging and quantity

Related products

Plastic mesh sleeve R-PLS 16x85mm - plastic bag - 10 pcs.

Plastic mesh sleeve for use with threaded rods in hollow substrates

Pump for blowing drill cuttings - plastic bag - 1 pc.

Manual blow pump for cleaning dust from drilled holes

Plastic mesh sleeve R-PLS 12x50mm - plastic bag - 10 pcs.

Plastic mesh sleeve for use with threaded rods in hollow substrates

R-BRUSH Metal brush for cleaning holes for M8 rods - label - 1 pc.

Metal brush with handle for cleaning holes in a solid substrate

Brickdrill SDS PLUS non-impact drill bits 10x260 mm - plastic hanger - 1 pc.

Drill bits for non-impact drilling in ceramic materials

R-BRUSH Steel brush for cleaning of deep holes, 12mm - plastic box - 1 pc.

Steel cleaning brush for cleaning drilled holes with the possibility of extension

Rebardrill SDS Plus drill bits 10x50x110 mm - plastic hanger - 1 pc.

High-quality SDS plus drill bits for drilling in reinforced concrete

Rebardrill SDS Max drill bit 12x200x340 mm - plastic hanger - 1 pc.

SDS max drill with 3 symmetrically arranged cutting edges allow, for drilling holes in reinforced concrete, concrete, stone and hard brick

Aggressor SDS Plus drill bits 10x50x110 mm - plastic hanger - 1 pc.

Drill bits SDS plus for fast drilling in concrete

Concrete cylindrical drill bits Impactor 12x200 mm - plastic box - 1 pc.

High-quality masonry drill bits consuming 20% less battery power while drilling hammer Cordless drill

Dustlessdrill SDS Max 14x400x600 mm drill bits - plastic hanger - 1 pc.

Hollow drill bits SDS max for dust-free drilling in reinforced concrete

Features

Polyester bonded anchor without styrene, recommended for medium loads, suitable for use in most construction substrates

  • Available in a winter version with faster curing time. It can be used from -20°C.
  • Product with wide spectrum of use in the medium load capacity area
  • Suitable for multiple use. Partly used product can be reused after fitting new nozzle
  • Approved for 15 substrates
  • Option of use standard manual silicone gun
  • The most convenient bonded anchor for general pupose use
  • Ideal for applications where mechanical anchors are not suitable
  • Three colors - standard, stone & gray
  • Easy dosage thanks to patented self-opening system and use of manual or electric gun

Product video

Installation and use of polyester chemical anchor – Rawlplug's tutorial

Substrates

Non-cracked concrete C20/25-C50/60

Non-cracked concrete C20/25-C50/60

Solid brick

Solid brick

Solid sand-lime brick

Solid sand-lime brick

Hollow brick

Hollow brick

Hollow sand-lime brick

Hollow sand-lime brick

Hollow lightweight concrete block

Hollow lightweight concrete block

Solid concrete block

Solid concrete block

Aerated concrete

Aerated concrete

Reinforced concrete

Reinforced concrete

High-density natural stone

High-density natural stone

Hollow-core slab

Hollow-core slab

Approved surfaces

Applications

Balustrades

Gates

Handrails

Sanitary and gas installations

Steel structures

Storage racks

Swings

Substitutes

Services

Resin calculator

Resin calculator

EasyFix

EasyFix

Training at the Rawlplug Academy center

Training at the Rawlplug Academy center

Technical Support 2

Technical Support 2

Installation guide

Installation manual

Installation step by step

1

Drill a hole to the required diameter and depth for rebar size being used.

2

Blow out the dust at least 4 times with the hand pump.

3

Clean drilled hole 4 times.

4

Remove drill cuttings from the hole using the hand pump four times.

5

Unscrew the cap and screw on the resin dispensing tip.

6

Place the cartridge in the dispenser.

7

When starting dispensing from a new package, discard approximately 10-15 cm of unmixed resin.

8

Fill with resin 70% of the depth of the hole, starting from the bottom of the hole.

9

Immediately after dispensing the resin, insert the rod into the hole with a twisting motion.

10

Remove the unnecessary amount of resin that flowed from the hole and wait for the appropriate time for the resin to cure.

11

A bonded anchor with a threaded rod is correctly installed in the concrete substrate.

12

Drill a hole to the required diameter and depth for rebar size being used.

13

Hollow substrates: insert mesh sleeve into the hole.

14

Solid substrates: Insert the mixer nozzle to the bottom of the drill hole and inject resin, slowly withdrawing the nozzle as the hole is filled to 70% of its depth.

15

Immediately after dispensing the resin, insert the rod into the hole with a twisting motion.

16

Remove excess resin that has flowed out of the hole and allow the resin to set properly.

17

Attach fixture and tighten the nut to the required torque.

18

Bonded anchor with the threaded rod is properly installed.

Approvals and publications

Technical library and approvals

Choose document:

ETA-21/0243

1488-CPR-0947/W

DoP-21/0243-R-KEM-II

ETA-12/0528

1488-CPR-0369/W

DoP-12/0528-R-KEM-II

UKTA-0836-22/6131

UK 0836-CPR-23/P6729

UKTA-DoP-22/6131-R-KEMII

UKTA-0836-22/6108

UK 0836-CPR-23/P6745

UKTA-DoP-22/6108-R-KEMII

KOT-2018/0134

KDWU-2018-0134-1

Hygienic Certificate - R-KEM II

VOC Emission Test Report - R-KEM II

SDS - R-KEM II

SDS_R-KEM-II_CFS_01.03.2023

Product card and catalogues

Choose product card:

Product cart

Product cart

Choose product catalog:

Specification Design Guide

General catalogue - PDF

Stay up to date

Sign up for our newsletter and don't miss:

Information

on our products and services

News

on the offering and latest promotions

Reports

on events, trade shows and industry conferences

© 2024 Koelner Rawlplug IP