Pump for blowing drill cuttings - plastic bag - 1 pc.
R-BLOWPUMP
5906675102412
Define product parameters:
Catalog price for pc:
PLN170.73
net | VAT 23
Contact with us and check out our terms of cooperation
R-BLOWPUMP
5906675102412
Define product parameters:
Catalog price for pc:
PLN170.73
net | VAT 23
Contact with us and check out our terms of cooperation
Catalog price for pc:
PLN170.73
net | VAT 23
Contact with us and check out our terms of cooperation
R-BRUSH Steel brush for cleaning of deep holes, 14mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 18mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 16mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 12mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 20mm - plastic box - 1 pc.
Manual blow pump for cleaning dust from drilled holes
Rawlplug R-KER Vinylester Resin - Rebar Installation
Cobblestone
Cracked concrete
Non-cracked concrete
Granite
Solid clay brick ≥ 20MPa
Hollow brick
Clay block
Hollow lightweight concrete block
Hollow block
Concrete hollow floor block (eg. Teriva)
Aerated concrete
Aerated concrete block
Brick
Solid concrete block
Approved surfaces
Anchoring glued in with threaded rods
Anchoring glued in with reinforcing bars
R-BRUSH Steel brush for cleaning of deep holes, 12mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 14mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 16mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 18mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 20mm - plastic box - 1 pc.
R-BRUSH Steel brush for cleaning of deep holes, 22mm - plastic box - 1 pc.
Rigid extension for mechanical cleaning with SDS+ drive R-BRUSH-TC - plastic bag - 1 pc.
Extension for R-BRUSH-TC with a handle - label - 1 pc.
Extension for R-BRUSH-TC with thread - label - 1 pc.
R-BRUSH Metal brush for cleaning holes for M8 rods - label - 1 pc.
Metal brush for cleaning holes M10 - label - 1 pc.
Metal brush for cleaning holes M12 - label - 1 pc.
Metal brush for cleaning holes M16 - label - 1 pc.
Metal brush for cleaning holes M20 - label - 1 pc.
Metal brush for cleaning holes M24 - label - 1 pc.
Design Consulting
Training at the Rawlplug Academy center
Technical Support 2
E-learning training
Drill a hole to the required diameter and depth for rebar size being used.
Clean drilled hole 4 times.
Remove drill cuttings from the hole using the hand pump four times.
Immediately after dispensing the resin, insert the rod into the hole with a twisting motion.
Remove excess resin that has flowed out of the hole and allow the resin to set properly.
Chemical anchors, general characteristics and application - E-LEARNING
Chemical anchors, basics of anchoring technology - temperature - E-LEARNING
Chemical anchors basics of anchoring technology - substrates - E-LEARNING
Chemical anchors basics of anchoring technology - rods- E-LEARNING
Chemical anchors general installation rules - E-LEARNING
Chemical anchors - introduction and correct installation of anchors - ON-SITE TRAINING
Chemical anchors - ON-SITE TRAINING
Chemical anchors - introduction and correct installation of anchors - TRAINING CENTER
Chemical anchors - Rawlplug's offer - TRAINING CENTER
Chemical anchors - introduction and correct installation of anchors - WEBINAR
Chemical anchors - Rawlplug's offer - WEBINAR